Poseidon 3468 je IP termostat podpira dva relejna izhoda, 4 vhodne kontake in 4 senzorje za temperaturo in vlago. Vsebuje tudi spletni strežnik, zunanji nadzor in obveščanje o preseženih vrednosti. Vrednosti in konfiguracija so na voljo prek spletnega vmesnika, vrednosti pa prek mrežnih protokolov (SNMP, XML, Modbus / TCP in drugi). IP termostat ima funkcijo lokalnega nadzora. 2 izhoda z 250V.
OSNOVNE ZNAČILNOSTI
Senzorji so povezani preko 1-Wire (RJ11), skupne dolžine napeljave do 30 metrov. Vsak senzor spremlja določene vrednosti in v primeru preseženih vrednosti ali vklopa/izkola kontakta o tem pošlje obvestilo prek e-pošte ali SNMP trap.
Sonde na voljo
Temperatura - Temp-1Wire, sonde različnih dolžin (1, 3 in 10 m)
Vlaga - Humid-1Wire, različne dolžina (1 in 3 m)
PowerEgg kontrola napetosti
Detektor poplave
Detektor uhajanja plina
Javljalnik dima
Detektor gibanja
TEHNIČNI PODATKI
-
Port 1: Ethernet RJ 45 - 10BASE-T / 10 Mbit/s
-
Port 2: SENSORS - 1-Wire bus (RJ12)
-
Port 3: 4 Dry Contact input for contact connecting
-
Port 4: 2 switching outputs of internal relay
-
Power supply : 12V SS
-
Device setting:
Port 1 - Ethernet port |
|
+ Interface |
RJ45 (10BASE-T) – 10 Mbit or 10/100 Mbit network compatible |
+ Supported protocols |
IP: ARP, TCP/IP (HTTP, Modbus over TCP), UDP/IP (SNMP) |
+ SNMP compatibility |
Ver:1.00 compatible, some parts of the ver 2.0 implemented |
|
Port 2 - 1-Wire sensor bus |
|
+ Connector |
RJ12 (6 pins - 4 pins used only) |
+ Sensors / distance |
model 3265 - max. 5 sensors, up to 10 m total
model 3262 - max. 2 sensors, up to 10 m total |
|
Port 3 - Dry contact inputs |
|
+ 4 Contact inputs |
Connect it with a contact directly (dry contact). |
+ Isolation |
Galvanic isolated up to 50V DC |
+ Sensor type |
NO or NC contact switch |
+ Max distance |
Up to 30 m |
|
Port 4 - Relay switch outputs |
|
+ 2 Digital outputs |
Control via network (Web, XML, SNMP) or signal local alarm |
+ Isolation |
Relay switch up to 50V DC, max DC current 24V/1A, 50V/0.5A |
+ Switch type |
3 pins, can be used as NO or NC contact switch |
|
LED Status indicators |
+ POWER |
Green - power OK |
+ LINK & Activity |
Yellow - Ethernet connectivity |
|
DIP SWITCH configuration |
+ DIP1 - RS--232 Setup mode |
Not used |
+ DIP2 - Security |
ON = Security mode - remote configuration disabled
OFF = Non-Security mode - remote configuration enabled |
|
Physical parameters |
|
+ Voltage requirements |
9 - 15V / 250 mA DC
coaxial power connector (barrel), GND on the shield |
+ Dimensions |
35 x 101.6 x 76.2 [mm] (H x W x D ) |
+ Weight |
150 g |
|
Functional parameters |
|
Device SETUP configuration possibilities |
- UDP Config - IP address assign via UDP with using PN Eye
- TCP Setup - Terminal configuration and sensors management
- WWW Setup - HTTP Flash application
- SNMP (just for some parameters) |